Page 1 of 2
[LOOK IT] STEP 3. Configure Fuel card
Posted: Wed Jun 08, 2011 3:31 pm
by ilya
OK! i have VTEC and chiped ECU. after 2 year, im happy
next step - it's configure fuel card... tommorow i send email to Russian "Famous" tuining group for made this operation.
they answer:
"we configure AT only with UICHIP and our ECU. PRICE - 650$"....
I think it litle expensive, and i already have ECU. i will find methodology for setup it.
what i need except O2 WideBand?
and what is it? it's common O2Sensor with monitor? or O2 sensor - special?
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Wed Jun 08, 2011 9:37 pm
by BETEK
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Sat Jun 11, 2011 10:36 am
by ilya
experimental firmware, is based on D16Z6 P28 AT for D14A4 with VTEC
-VTEC 4560
-rev im 6816
-speed limiter 105mph ~ 168kmh
-No knock sensor
-No oxygen sensor heater
http://www.ej9.ru/data/bin/EJ9_p28_0611.bin
firmware by 1net , is based on D16Z6 for D14A4 MT (i use it in AT)
i recomended it for start after swap to OBD1.
-No knock sensor
-No oxygen sensor heater
-rev limit ~ 7200
http://www.ej9.ru/data/bin/d14vt_final.bin
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Mon Jun 20, 2011 9:14 pm
by Dodo Bizar
On a sidenote: if you can, increase revs, 7200~7500 engine can cope with that normally. Though probably the AT shifts too soon to have any effect?
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Tue Jun 21, 2011 6:22 pm
by ilya
I reduced the REV, because I'm afraid of the big turns. never did not go to such speeds, I'm afraid of engine failure.
+ In a week I'll change the piston rings, and REV still undervalued, just in case. precautions. I will experiment later with REV.
Now I have found the approximate setting cards for 1.4 AT With p28.
decreased consumption of gasoline) PGMFI cool!
+ Add VTEC
+ At low speed once the car started to go better!
I think our job is close to the machines 1.5.
not VTEC-E, a real aggressive VTEC!
later i upload it, in august i want make dynotest.
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Tue Jun 21, 2011 8:09 pm
by Dodo Bizar
Yes you are right about keeping revs low with the current situation of the engine. Looking forward to your dyno!
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Thu Jun 30, 2011 7:38 am
by ilya
in august Man) i waiting it too)
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Thu Aug 18, 2011 9:15 pm
by ilya
anyone else is doing? how many people who have replaced the OBD1?
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Fri Aug 19, 2011 3:40 pm
by mynameisowen
So let me get this right, you are making your own map for your ECU?? What software are you using?
Re: [LOOK IT] STEP 3. Configure Fuel card
Posted: Fri Aug 19, 2011 9:51 pm
by ilya
CROME, just CROME and software for programmer PicProg+ for flashing memory. now i write my own editor for LINUX =) because CROME didn't work here((