EJ9 Suspension and Chassis specification

From soft stock to hardcore track, what do you use?
User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

EJ9 Suspension and Chassis specification

Post by saxophonias »

As the title suggests here we are going to provide information about stock ej9 chassis and suspension. Everything about chassis' dimensions, weight, suspension, wheel alignment etc.
Last edited by saxophonias on Wed Jul 15, 2009 11:42 pm, edited 1 time in total.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

Image
Image
Image
Image

Front Double wishbones
Image
Last edited by saxophonias on Sun Jul 19, 2009 11:42 pm, edited 1 time in total.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

98-00 civics were only mounted with front swaybar which was 22mm.
Image
If your ek civic is equipped with front swaybar, then any other bigger will fit as the pattern is the same and the only difference is in diameter.
As for the rear suspension, there isn't any swaybar installed. Still there are the holes on the wishbones to accept any kind of swaybar. This means that you can swap bigger aftermarket swaybars without having to change control arms or drill etc.
However here you have to consider something crucial. Stock ej9/ek2/ek3/ek4 rear subframe isn't so strong to accept swaybars bigger than those of Si, SiR VTi etc that is 12-13mm. The bigger the swaybar the more possible to tear apart the subframe. So beware.
To solve this issue you can purchase aftermarket bars (ASR, BEAKS etc). We will discuss this in another topic.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

The rear suspension set up
Image

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

I'll soon post pictures of ej9 front lower control arms. They are the one piece style identical to ek3/ek4/ek9.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

As promised. Here is a picture of the one piece style lower control arms of ej9.
Image
This is the Eg/mb/ma/ style front lower control arms.
Image
Please verify that.

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

This is the EK chassis
Image

User avatar
mynameisowen
Posts: 1307
Joined: Thu Aug 20, 2009 3:38 am
Location: London or Oxford, England
Contact:

Re: EJ9 Suspension and Chassis specification

Post by mynameisowen »

awesome post, very informative. One question for you guys, what tyre pressures do yo guys normally inflate too?? I tend to do 32 front 31 rear, but my car didnt come with a stamp saying what it should be on the door :(

Bearing in mind fuel economy handling and tyre life is affected by tyre pressure, what do you guys use?
1996 EJ9 Civic
1998 BB8 Prelude Motegi VTi
1998, B16A2 EK4 Civic VTi

Aims:
EJ9 - Now my GF's car.
BB8 - Rebuild after crash damage to front end.
EK4 - Daily driver. Strip and track prep once prelude project complete

User avatar
baz
Posts: 427
Joined: Tue Oct 06, 2009 3:57 pm

Re: EJ9 Suspension and Chassis specification

Post by baz »

2.1 bar with minimum weight, so 2 persons and some baggage.

2.3 bar with four passengers and baggage.

2.4 bar with a caravan or trailer etc.
D14A3-OBD1-I/H/E
126 hp /145 Nm

User avatar
saxophonias
Posts: 2592
Joined: Fri Jul 03, 2009 6:03 am

Re: EJ9 Suspension and Chassis specification

Post by saxophonias »

it's a bit subjective this issue. Bearing in mind the manual i wouldn't go less than 32 and more than 35.

Post Reply